January 15^th, 2011 OFFICIAL RULES

 If you can not print these, email me at johnny@nflbk.com and i will send a copy to you.

IF IT IS NOT SPECIFIED IN THE RULES BELOW THAN CALL FIRST BEFORE YOU ATTEMPT IT

Note any changes from last year are highlighted in blue. Latest

Latest Revision Date is 1/15/2011

1-       Any year O.E.M. frame and body model of passenger car or station wagon except for the following:

2-       1973 or older Chrysler Imperials or Lebaron’s.

3-       For 80’s and newer class, cars are allowed to do a coil to leaf spring conversion:

1. General motors’: any 1977 or newer.
2. Chrysler: any 1979 or newer is allowed.
3. Ford: any 1978 or newer is allowed.

4-       We reserve the right to and re-inspect cars at any time before, during or after the event, even after it has been flagged. You may be asked to cut areas of question open before, during and after the derby if needed.

WE ARE PRIVELIGED TO USE ALL OR OUR  FACILITIES! PLEASE TAKE EXTRA CARE IN STRIPPING YOUR CAR!

PREPARATION:

1-       All glass, plastic, and pot metal must be removed. Nothing may remain in the bottom of the doors, trunks. All outside hardware must be removed (door handles, mirrors, chrome, molding, screw, fiber glass, etc). Inner wagon panels may remain but all rear seats must be removed.

2-       No added weight to the car except the weld. No packing the frames, trunks, passenger doors, or under floor decking.

3-       Front seats must be securely mounted to the floor, and must have seat belts. All cars MUST have inner padding on driver’s door.

4-       All flammable materials inside the car must be removed except necessary safety padding and seat.

5-       No stadagoning is allowed. Contact head Official if you have any questions

6-       Skid plates are allowed, but must be separate oil pan/transmission plates. No full-length skid plates. No bolting or welding of skid plates to the frame or body.

7-       Your number must be at least 18 inches tall and must be painted on each side of your car.

8-       Roof signs are mandatory at HR4th show.  Roof number at least 18 inches tall securely fastened to the roof with your number on each side. It is to be placed as far back on the roof towards the trunk as possible. Ideal location is over the rear seat.

9-       VIN number tags must remain attached and accessible on the car for inspection for 80’s and newer class cars.

10-   ALL CARS MUST BE COMPLETE BEFORE BEING INSPECTED. ONCE INSPECTED YOU ARE NOT ALLOWED TO TAKE YOUR CAR BACK TO THE PITS TO WORK ON THEM.

Fuel Pumps:

1-       Externally mounted electric fuel pumps are allowed. ON/OFF off switch must be located on the dash board so that they are easily accessible to officials. Switches must be painted in a florescent type paint making them stand out from other switches. Safety to be determined by officials on racing fuel cells.

Tires:

1-    You may use any tire and you may tube, screw, glue, tire inside of tire, flappers, and use recaps) only Air must be used to inflate your tire.

2-       You may weld valve stem protectors.

Brakes:

1-       All cars must exhibit the ability to stop before entering the arena. If a car loses its braking ability it will be subject to disqualification.

Engines and DP protectors

In an effort to keep this simple and fair:

1.  Distributor protectors may only be bolted to the motor
2. If your distributor is in the rear of the car, the protector may be a max of 12” wide and no farther than 3” from the distributor cap and no more than ¼” thick
3. If you have a front distributor, the rear support plate may only be 12” wide but may not be more than 1 inch from the block and no higher than the valve covers and no more than ¼” thick.
4. DP must be a minimum of 5 inches from the dash bar, window bar or any added metal.
5. Engine cradle must be mounted to the frame cradle only. No other part of the cradle or DP may be mounted to the frame.
6. Pulley protector may not be more than 2“ from the front of the pulley and no more than ¼” thick
7. IF YOU HAVE ANY QUESTIONS SEND US A PICTURE FOR APPROVAL

1. Two additional motor ties downs may be used but must attach to the block or heads and not the engine cradle or DP protector. No more than ONE fastener on each side of the motor may be used. If straps are used they may only be welded, within reason, to 3 inches per side on the frame. That section that is welded to the frame may not be any thicker than ¼ inch thick and 2” wide, and MAY NOT extend in front or the water pump or behind the engine block any more than 4 inches. One chain from the rear of the motor heads/manifold to the dash bar may be used to keep the motor from coming forward.
2. Any engine and transmission combination may be used in any car, but must be mounted within 4 inches of the original motor. Must be mounted securely. You may cut a hole in the firewall to accommodate the engine within reason. However it must be covered to prevent a fire hazard
3. You may cut a hole to accommodate the distributor. However it must be covered to prevent a fire hazard if opening is larger than 8” x 8”. Distributor protectors are allowed see above.
4. Holes left in the firewall more than 8” by 8” from removing the dash and heater must be covered to prevent fire hazards.
5. No holes will be allowed in the floor of the car except to accommodate the transmission shifter, fuel and transmission lines and wiring. Shifters may be tack welded or bolted. Patching holes is for safety not reinforcement, if patching rust holes you may use sheet metal only not to exceed 2 inches past rusted area.
6. Motor mounts may be welded; when making motor mounts to raise shift or use different motors in different cars, mounts cannot exceed original footprint of motor mount. Transmission and motors may be chained or strapped with no reinforcing of the engine frame cradle. No more than ONE fastener on each side of the motor may be used. If straps are used they may only be welded, within reason, to 3 inches per side on the frame. That section that is welded to the frame may not be any thicker than ¼ inch thick and 2” wide, and MAY NOT extend in front or the water pump or behind the engine block any more than 4 inches. One chain from the rear of the motor heads/manifold to the dash bar may be used to keep the motor from coming forward.
7. You may tilt your rear end by shortening or lengthening rear end control arms; however, they must remain functional. Do not reinforce more than one inch past cut or extension area, must use metal of same thickness or less, no other welding other than the cut seam is allowed. Cuts must be made in the middle of the arms, and no metal added to the inside or ends of the control arms.

Rear ends:

1. 1.       Any 5 lug rear end may be used.

FOR USE BELOW:

1-      Note due to the price of metal we will use a “within reason” clause; however if you push it we will make you cut it!

2-      Only 3/8” round hot, cold or rebar, or 1” x 3/16” flat strap may be used for seam welding.

3-      Chain must be no larger than 3/8” when chaining.

4-       #9 wires may be used in place of chain only and only 4 strands may be twisted together.

Securing:

1-       Only bolts no bigger than 3/8” X 2” may be used around any hood cut out openings. Must be spaced 12” apart and no more than 3 inches from the cut out opening. NO zip screws can be used anymore.

2-       Only one of the following (welding or bolting) must be used to secure your hood and trunk. The tailgate of a station wagon will be treated as a trunk. #9 wire may only be used in place of chain were chaining is allowed.

 Doors and windows:

1-       Doors may be fully welded. All EXTERIOR door seams may be welded OR you may chain or use #9 wires, at least twice per seem. If chaining or wiring, none may go through the frame.

2-       A protective bar may be placed inside or outside on the driver’s and/or passenger’s front door. It cannot extend more than 6” past the driver’s door seam on either side.

3-       No window openings may be snaked through quarter panels to the roof with chain, cable or wire.

4-       One or two bars running from the roof down to the cowl or front dashboard bar is mandatory! One or two bars from the rear speaker deck area to the roof is optional, No more than two bars may be used in either location and bars can not exceed 2 inches in diameter and be welded NO MORE THAN 3 INCHES BEYOND THE LIP OF THE GLASS ONTO THE TRUNK. AND THE MOUNTING PLATE MAY ONLY BE 4” BY 4” IF MOUNTED IN THIS AREA. On four door cars without posts you may add a chain or a bar from the top center of the doors to the roof.

5-       DOOR seams ONLY may be pinched and welded were the windows come up through.

6-       You may use a screen or netting over drivers side front window and drivers door only.

Interior bars:

1-       All interior bars must be a minimum of 2” outside diameter or a have minimum of a 6 x6 1/2” end plates. End plates are MANDATORY on all bars and must be welded in place no bolting allowed.

2-       Pipes cannot be fence, galvanized, exhaust style of pipe/tubing.

3-       A bar behind the seat is mandatory. It must be located no more than 6” from the final resting position of your seat.

4-       A minimum of one upright post or roll loop, halo MUST be used if a 4 door non post car and highly recommended on all cars. It must be ATTACHED to the floor (not frame) roof and seat bar. Located behind the driver’s seat. It may be welded or bolted to the floor. This is for safety so please make sure it is welded adequately or bolted.

5-       IF YOU WISH TO RUN A TUBE FROM EACH CORNER OF YOUR CAGE TO THE FLOOR PAN YOU MAY. THEY MUST BE VERTICLE AND WELDED ONLY TO THE FLOOR PAN AND MAY NOT PENETRATE IT TO THE FRAME OR MAY NOT BE ATTACHED TO ANY FRAME MOUNTING POINT OR SUBFRAME MOUNTING POINT.

6-       An optional bar may be put in the front where the dashboard was located, in between the front door posts.

7-       You may weld a connecting bar on the inside of the driver’s and passenger door only from front bar to the rear bar creating in essence a box.

8-       All bars and posts in the proximity of the head must be padded.

9-      Overall safety will be determined by the official’s at time of inspection.

Welding:

1-       Cars with 2 piece fenders may weld ½ of the exterior seam (call before welding).

2-       No inner seam welding or alterations to strengthen the frame or uni-body is allowed other than what is specified.

1. Exception is the inner rear panels of a wagon. They may be secured by FOUR 4” welds per panel seam. And a min of a 15” inspection hole must be made.
2.  You may weld the floor pan seam under the gas and brake pedal only for safety, no filler may be used. 

3-       All exterior hood and trunk seams may be fully welded. A seam is defined as two original exterior body to body lines on the doors hood and trunk and the front dashboard side of the hood only. No other seams or created seams may be welded other than on rule Door Window rule #6.

1. A seam runs from one corner to another, and is not continuous.
2. The tailgate of a station wagon will be treated as a trunk.

4-       In addition to the weld, two bolts not to exceed 1” in diameter and two washer’s not to exceed 3” in diameter may be placed thru the trunk lid and floor. Bolts may go through the frame or uni-body and may replace only 1 body mount and bushing per frame rail in the trunk floor pan area or it may be welded to the side of the frame. If welding the body mount may NOT be removed. Washers no bigger than 3 inches may be used.

5-       No painting or undercoating may be used underneath the car.

Bolting:

1-       Instead of welding your hood and trunk you may use 8 bolts to secure the hood and 8 bolts to secure the trunk. (using two 8 inch long by Two inch angle back to back over a seam with Two bolts acceptable)

2-       None of these bolts may go thru, around, or touch the frame or uni-body.

3-       Bolts may not exceed 1” inch in diameter or 8 inch’s in length.

4-       Washers may not exceed 3 inches in diameter.

5-       In addition to the eight 8” bolts, two bolts not to exceed 1” in diameter and two washer’s not to exceed 3” in diameter may be placed thru the trunk lid and floor. Bolts may go thru the frame or uni-body and may replace only 1 body mount and bushing per frame rail in the trunk floor pan area. Washers no bigger than 3 inches may be used. If welding the body mount may NOT be removed. Washers no bigger than 3 inches may be used.

EXAMPLE: You may weld the hood and bolt the trunk or visa versa, but not both on the same section.

Chains or #9 wire:

1-       3/8” inch chain is allowed to secure front and rear bumpers to the frame. Only two chains may be used. It may loop thru the hood or trunk. Excessive chaining (more than 2 wraps) will not be allowed.

2-       No chain may be welded at any point to the frame or body.

3-       You may weld a 3” washer to the hood to run the chain thru.

4-       You may use on the bumpers, in place of chain up to ¾ inch rolled steel or 2” x 3/16” wide flat strap welded from the upper core support area of the hood to the chrome of the bumper. No more than 2 of these may be used per bumper. It may only be welded up to 6” inches on the body and on the chrome. If bolting hood or trunk this cannot then be welded to the seam.

Bumpers:

The intention of this rule is to allow you to mount the bumper in such a way that it will not fall off. Upon inspection if it is determined that you have exceeded the intention of the rule you will be disqualified.

1-       Stock O.E.M. bumpers of passenger cars must be used.

2-       Bumpers may be cut so they do not smash into the tires during the event. Chrome may be welded to the inner bumper box to keep it from separating. 

3-       Bumpers may be flipped.

4-       Bumpers may be welded to the brackets and the frame only.

5-       Only One bumper bracket per frame rail may be welded to the frame, and can be welded and/or bolted no more than 10 inches from the front of the frame.

6-       If swapping bumper and brackets:

1. You may only use the mounting hardware that was on the car originally or one style of car bracket hardware and a car bumper. All other hardware must be removed. (ex. Chrysler bumper with GM shock brackets on a Ford)
2. Shock tube will be considered the bracket if disassembled from the mounting hardware. If this is done then rule #5 applies.
3. Mounting brackets may not be attached to the Cordoba type sub or k-frame in any way.
4. If using an Aluminum beam bumper you may weld your front straps around and to the bottom of the bumper bracket

7-       Compression bumper shock tubes may be compressed and welded.

8-       No material may be added other than the weld.

9-       No chrome may be welded to the body on compression bumpers whether it is using the mounting hardware or not. Non-compression bumpers may weld ORIGINAL bumpers to the body.

10-   No welding of any kind other than what is specified and straps (rule #4 chains or #9 wires) is allowed on the bumper.

Frame:

1-       THERE IS NO WELDING OF OR TO THE FRAME or UNI-BODY ALLOWED OTHER THAN what is specified in the Bumpers section #5 and Radiator Rule #4 and Engines Rule #5.

2-       If you cut the frame for pre-bending purposed, you may not weld the cut back together.

3-       All body mounts (rubber biscuit and cone) and “Pucks” must be in place. You may not remove bolts and place washers on both sides.

4-       No Buffing, grinding or packing of frames

5-       Humps may be chained with one wrap, but may not be welded to frame.

6-       No Chrysler sub-frame chaining other than the rear humps and on the K frame front frame in front of the motor using only 2 wraps around the FRAME only  

7-       No Imperial sub frame swaps allowed.

8-       1980 and newer model cars with coil spring rear ends may plate the rear frame humps using one plate per rail that is 7” X 4” X 1/4” thick max.  Cars that have leaf springs or have been converted to leaf springs MAY NOT plate the humps.

9-        

80’s Fords YOU MAY PITCH, TILT, TIP THE FORDS IN THE FOLLOWING WAY

You can cut flaps on front outside of the frame to pitch the frame, but pitch can be no more than ½ in. and no other metal or gussets can be added. Nothing is to be welded on the side of the spring bucket behind the ball joint. You may have a 5 inch long piece of angle welded to frame to set the cross member on if you like. Do not reweld any of the crush box seams
The only welds on the entire frame are :

1.      A arms forward topside only    

2.      Flaps on the front frame for the pitch

3.      Bumpers to frame

4.      The piece of angle for the cross member.  Any other welds on frame will cause car to be disqualified!

5.      YOU MAY NOT REWELD ALL OF THE CRUSH BOX SEAMS… PERIOD

6.  You may not swap out aluminum engine cradles.

7.  upper control arms and spindles may be swapped.

YOU MAY “COLD” PITCH THE FORDS AS WELL.

Radiators & Radiator supports:

1-       Only OEM style passenger car radiators may be used. Aluminum racing of the same style may also be used. Radiator hose loops may also be used.

2-       Radiators FIN area only may be sleeved in a light expanded metal. I t may not be fastened to any part of the car.

3-       Radiators must stay close to stock position in front of the motor. (No added water capacity).

4-       Engine coolants are allowed.

5-       Upper Radiator supports may be welded to the hood using a 6-inch weld only or may be bolted with two bolts with 3” washers. This may be done whether you use the eight-bolt rule or weld your hood. No more than 2 bolts may go thru the upper core support. And none if you weld it.

6-       Lower Radiator support body mount bushings may be removed and replaced with a max. 1” bolt diameter. Bolt may go up through the upper core support or hood to be used in #3 above.

7-       If when the body mount is located in front of the core support and you use the bolt there, a nut may be welded to the top of the frame only, ½” inch behind the core support. This nut only will be used to screw a bolt into to continue up thru the upper support. If an “S” Body Chrysler (call if you need to know what this is) you may drill a hole completely thru the frame to run the all thread thru as stated above, must no more than 1” behind core support.

8-       Radiator support may not be welded to the frame, bumper, bumper brackets or anything else.

Transmission coolers:

1-       Transmission coolers will be allowed.

2-       Proper hydraulic, Metal or steel braided line must be used.

3-       Condenser must be enclosed or covered.

4-       Overall safety will be determined by the official’s at time of inspection.

Gas Tanks:

1-       Original gas tanks must be removed from the car.

2-       You must have your gas tank securely mounted inside the car with a minimum of two fasteners, behind the driver’s seat and covered unless a fuel cell or metal tank. Seat belts or “pull” type straps may not be used.

3-       A maximum size of 6.5 gallons can be used.

4-       A marine type tank or fuel cell must be used. NO plastic gas cans will be allowed unless they are mounted within a four sided metal tank protector. (call for clarification)

5-       GAS TANK PROTECTION BARS MUST NOT BE ATTACHED TO THE BODY IN ANY WAY, AND MAY BE ONLY SLIGHTLY LARGER THAN THE GAS TANK ITSELF.

6-       Fuel lines must run inside car. Original gas line inside frame cannot be used.

7-       Overall safety will be determined by official at time of inspection.

Battery:

1-       Only one battery of any type may be in the car.

2-       It must be securely mounted inside the car in front of the seat and covered unless a gel cell.

3-       Battery Box can not be made out of plastic; Seat belts or “pull” type straps may not be used.

4-       Battery Box may not roll over or be bolted thru the frame.

5-       Overall safety will be determined by official at time of inspection.

Air Cleaners:

1-       You must have an air cleaner over the carburetor all times during the event.

2-       No starting fluid will be allowed.

3-       There must be a minimum of 40 square inch opening cut around the air cleaner in case of a fire.

4-      Overall safety will be determined by official at time of inspection.

Cut outs:

1-       Cut outs over the wheel wells are legal.

2-       Cutouts may be folded If cutouts are folded you may be asked to cut an inspection hole in them.

3-       Only three 3/8” bolts with 1” fender washers, directly over the fender’s, may be used.

4-       No welding of the cutouts is allowed.

5-       You must have TWO holes cut in the trunk lid for inspection. Minimum of 8” in diameter unless tail light hole are big enough.

6-       If your hood is welded must have a minimum of a 30” by 30” hole cut in the hood for inspection. If bolted, hood must be off of car during inspection. Unless the 30 by 30 cutout exists.

7-       If inspection holes & fire holes are determined to be too small you will be asked to cut them larger.

8-       If center cut out is bent forward to cover the radiator it may not be fastened to the bumper.

Trailer Hitches:

1-       Trailer hitches and framework after Market or not must be removed.

Suspension:

1-       No pulling shocks and putting pipes in their place

2-       You may use tires, spring swapping or spacers , or WELDING ON EACH SIDE OF THE UPPER A-ARM WITH NO MORE THAN A 2 INCH BY 1 INCH WELD PER SIDE TO HOLD THE A-ARM TO THE FRAME.

3-       may be used to raise the cars suspension.

4-       No adding reinforcements to the suspension.

5-       No putting leaf springs on top of the axle.

6-       You may weld coil springs to the frame or axle so they do not fall out (no filler may be used).

7-       You may not clamp the shocks. No solid suspension.

8-       You are allowed 9 leaf’s maximum. All Leafs after the main must be a minimum of 3” shorter than the one above it on each end.  You may not put anything on top of the main leaf, except factory OEM overload spring. In which case if using a 7 leaf spring pack you may not use an overload spring. Any clamps used to secure this spring will be considered one of the clamps in rule #8

9-       You may use only 3 clamps total per leaf spring pack, no welding. Springs must be of passenger car origin. Clamps may be no wider than 3” using only one set of bolts per clamp.

10-   Original leaf spring cars must be mounted in original mounting position. 

11-   Coil spring to leaf spring conversions are allowed in all 80’s and newer cars. Attachment point on the frame can be no more than three inches.(ie, size of a shackle)

12-   On 1978 and older Ford and Mercury cars, ball joints, upper control arms and tie rods may be strengthened.

Rules for Previously Run Cars

The following rules apply to previously run derby cars only.  The intention of these rules is to help you make your pre-run car competitive with fresh cars.  The idea is to repair damaged areas only and return the car to as close to “stock” condition as possible.  This is not an opportunity to plate or reinforce your car!   If we feel that you have pushed the limits of these guidelines, you will not be able to compete!  Inspection officials will use discretion and all decisions will be final.  Call and ask before you fix something that is not outlined in this section.  Absolutely NO ADDED METAL other than what is specified below!

1.  GENERAL.  You may make any change or modification that complies with the full set of general rules.       (Add all-thread, strap, and bolts; weld doors, etc…if the car was previously run somewhere that does not allow these things.)  There are certain rules and items that are MANDATORY for this show, so make sure you read the rules completely.  Call if you have questions.  Keep in mind that you may have to cut welds, bolts and/or make other modifications to be in compliance with the rules.

2.  SAFTEY.  You may patch any hole in the doors or floor of the car for SAFETY ONLY.  You must use sheet metal only, and your patch may only be 2” larger than the hole you are patching.  Safety will be determined by inspection official at the time of inspection.

3.  FRAME REPAIRS.  Pre-run cars are allowed to repair damaged areas of the frame on the front and rear of the car (4 total repairs on the car max!).  You may use one patch that is 6” x 4” x 1/8” thick MAX plate for each repair.  The patch may only be placed on the part of the frame that is damaged.  There must be a clear sign of damage from a previous derby. (Tear, crack, or extreme bend).  This will be reviewed by the official at the time of inspection.  The patch must be placed FLAT on the top, bottom, inside or outside rail.  It MAY NOT be welded and folded over from one side to the other.  Patch may NOT be welded to any other patch or ANY other part of the car.  (Body, bumper, bumper bracket, core support, inner fender, all thread, etc…)  Patch may be welded only!  NO BOLTS!  No other frame welding will be allowed!  All other repairs made to the frame will be cut and/or removed.

If you have other pre-run questions, call first before you fix it!

STOCK CLASS RULES:

1.             NO CHRYSLER IMPERIALS (73 and older)/LINCOLN CONTINENTALS (69 and older)

2.             ALL GLASS, PLASTIC, SCREWS, POT METEAL, FLAMMABLES, ETC. MUST BE REMOVED. NOTHING MAY REMAIN IN THE BOTTOM OF DOORS. ALL EXTERIOR HARDWARE AND CLIPS MUST BE REMOVED.

3.             HOOD MUST BE OPEN FOR INSPECTION.OR MINIMUM OF 30 BY 30 HOLE MUST BE IN HOOD.

4.             HOOD AND TRUNK MAY ONLY BE CHAINED USING SIX CHAINS ON EACH /OR SIX BOLTS NO LONGER THAN 8” ON EACH WITH TWO 5” WASHERS ON EACH SIDE (two 6” lengths of 1 ½” X 1 ½” may be welded on the hood seam back to back using one ½” bolt to pin them together) YOU MAY MIX AND MATCH THE ABOVE AS LONG AS ONLY SIX ARE USED ON HOOD AND TRUNK.

5.             NO SCREWS/ BOLTS OTHER THAN WHAT IS SPECIFIED MAY BE USED ANYWHERE.

6.             HOLES IN THE HOOD ARE FOR HEADERS AND A MANDATORY MINIMUM 12” FIRE HOLE ONLY. NO WRAPPING OF ANY SHEET METAL ALLOWED.

7.             EXTERIOR DOOR SEAMS ONLY MAY BE FULLY WELDED.

8.             INTERIOR WELDING:

                A.            FOLLOW GENERAL STANDARD RULES LISTED ABOVE FOR DRIVER COMPARTMENT AREA

9.             GAS TANK, BATTERY AND TIRES MUST FOLLOW ALL RULES LISTED ABOVE IN REGULAR RULES.

10.           BUMPERS MAY NOT BE SWAPPED WELDED OR TOUCHED IN ANYWAY OTHER THAN TO DRILL A HOLE IN THE SHOCK TO ALLOW THE BUMPER TO COMPRESS. CORNES MAY CUT.

a. 1 CHAIN PER SIDE OF BUMPER TO HELP HOLD ON. (1 wrap only) IF IT GOES THROUGH HOOD, THAT COUNTS AS ONE OF THE HOOOD MOUNTING POINT’S

b. BUMPERS MAY BE FLIPPED

11.           MUST HAVE STOCK OR COIL OVER SHOCKS. NO WELDING STUFFING OR CLAMPING OF SHOCKS. SUSPENSION MUST BE STOCK AND UNCHANGED. COIL SPRINGS MAY BE WELDED TO THE AXLE HOUSING, SPRING SPACER MAY BE USED.

12.           YOU MAY CUT THE FENDER WELLS FOR TIRE CLEARANCE. NO ROLLING OR BOLTING OF FENDERS.

13            ENGINES MAY BE SWAPPED BUT MUST REMAIN CLOSE TO ORIGINAL POSITION AS POSSIBLE. NO CUTTING OF FIRE WALL TO ACCOMMODATE DIFFERENT MOTORS. A HOLE MAY BE CUT FOR THE DISTRIBUTOR. MOTOR MOUNTS WITH ONLY ONE STRAP OR CHAIN TO THE TOP OF ENGINE CRADLE, NO WELDING TO THE FRAME. NO ENGINE PROTECTION DEVICES ALLOWED.

14.           AXLES AND HOUSINGS MAY NOT BE CHANGED. GEARS MAY BE WELDED OR POSI’D

15.           ANY TIRES MAY BE USED ALLOWED

16            Final determination will be made by officials

THIS IS A STOCK CLASS. IT IS INTENDED FOR FUN. IF IT ISN’T IN THE RULES THAT DOESN’T MEAN YOU CAN DO IT, SO PLEASE CALL IF YOU HAVE ANY QUESTIONS.

TRUCK CLASS RULES

1. 1.      Any Standard 2 or 4 wheel Truck, Suburban, Blazer, Bronco and full size van type vehicles are allowed. If you are in question please call first.
2. 2.      ALL GENERAL STANDARD CAR BUILDING RULES APPLY, SEE ABOVE.
3. 3.      Any fiberglass roofs or shells must be removed and car stripping rules will apply.
4. 4.      Driver’s door and door posts near the driver must be padded.
5. 5.      DOOR BARS ARE MANDATORY ON Drivers door
6. 6.      For Trucks with beds:
7. 1.      Bed must be welded to the cab to maintain the integrity of the gas tank mounting area.
8. 2.      A 6 gallon (max) fuel cell or metal gas tank must be mounted at the front of the bed.  A spreader bar with end plates MUST be welded in near the tank at the front of the bed to protect the tank. Bar must be no more than 3’ behind the cab. Tank should be covered to prevent gas from splashing in case of rupture.
9. 3.      A secure net is mandatory for the back window of single cab trucks to prevent whiplash.
   1. 7.      All tail gates must be fully welded.
   2. 8.      If truck has a beam type bumper it may not be welded to the body.  You may weld a “tin” type bumper to the body.  (call if you have questions)

Overall Safety will be determined by the officials!

OVERALL SAFETY IS OUR GOAL AND WILL BE DETERMINED BY THE TRACK OFFICIALS!

Rules of Competition:

1-       No intentional hitting the driver’s door (must be determined by TWO track officials unless it is deemed blatant). If you hit a driver’s door under power you will be disqualified from the heat and loose your place standing.

2-       No sandbagging. (Determined by track officials).

3-       No intentional hitting of a non-flagged car.

4-       Hit rule time will be determined at each show

5-       No team driving.

6-       The definition of a hit is as long as your car is running and able to make a hit unassisted in a forward or reverse motion under power. Rocking will not be considered a hit!

7-       Drivers must stay in they’re safety belts at all times during competition with your helmet on.

8-       As cars will be staged for the event, there will be no tampering of opponent’s vehicles. Any one caught tampering will be disqualified from this and any future events. This applies to your whole crew.

9-       Drivers must wear a D.O.T. approved full-faced crash helmet. (No add on chin guards). Eye protection is required.

10-   NO pit crewmember may enter the arena to help remove your car. Drivers may not provide their own tow vehicle.

11-   You must wear long pants and a long sleeve shirt, no shorts and no open shoes. Fire suit is optional.

12-   If a driver enter 2 cars. They must drive both cars in the heats. If both cars qualify then they may choose the car of their choice to run in the Main event. Another driver may be designated to drive the second car, but must have already been issued a pit pass and signed all waivers for that day’s event.

13-   Any instances resulting in a tie. Money will be split and trophy flipped for.

14-   If your car is rolled on its side or flipped over you will not be allowed to compete any further in that heat; however your time continues as if you were stuck.

15-   If you have 2 fires of any kind that need extinguishers to put it out, you will not be allowed to compete any further in that heat; however your time continues as if you were stuck. If you must be removed from your car for safety reason your time will run out accordingly.

16-   Once you are timed out or disqualified you may not help other drivers. Both you and the driver you assist will be disqualified for the heat.

17-   All official’s calls are final. If you disagree with a call sorry, arguing with an official or member of the staff or other drivers are grounds for disqualification. No calls will be overturned.

18-   No hot rodding in the pits or you will be disqualified.

19-   Un-sportsman like behavior will not be tolerated and will result in disqualification and removal from grounds.

20-   If a heat is stopped due to unsafe conditions, any cars still competing in that heat only will split the prize money evenly. Any heats that have not yet run will be refunded they’re entrance fee.

21-   Other than what has been specified above, no other alterations or interpretations of the rules will be allowed.

PROTEST RULE:

1-       If you wish to protest a drivers car you must:

1. Pay $200 to the head official and state your protest.
2. Be specific on what you are protesting (you can not protest the entire car).
3. If protest is found to be true, you receive your $ back and violating driver will be disqualified.
4. If protest is not substantiated by Head Inspector, you loose your $ and the driver being protested receives the $.

Miscellaneous:

            Numbers:

2-       No obscene words or graphics on the cars.

Decoration:

3-       Any decorations that are used must be made out of cardboard or foam.

4-       Be advised that by participating in this event you and your car may be filmed. And that the use of your image, likeness, voice and actions for photo, video and print use, sale and marketing.

Feed back:

1-       We encourage all feed back good and bad, but please do it in an adult and respectful manner. Please call or send your comments to us.

For more event information, registration or questions please contact:

Note: To avoid any issues state your question to any of the below officials, we will talk it over first so we are on the same page and then call you with an answer.

Johnny Gullo                                                       

Home                     801-732-9423                     

Mobile                   801-458-3990                     

E-mail                    johnny@nflbk.com

Address  4670 South 4650 West, West Haven, Utah 84401

Jim (Gumby) Simko

Mobile                   435-496-3636

Mitch Zellis           435-757-7948

Or visit us at our website:

www.stirrindirtracing.com

SATURDAY, OCTOBER 8th

1-       Registration:

1. REGISTRATION,  Car and Driver free
2. Extra Pit passes will be available.
3. Pit passes will be $25 after 5pm! Wristbands must be worn at all times. If it gets torn off, bring it to us and we will replace it. If you should loose it you must purchase a new one.
4. If the driver or pit crew is under the age of 18, he or she must have a release form from their parent or legal guardian. No one under 16 is allowed to drive. Release forms available upon request on the day of the event.

2-       Payouts:            $15,000 Total minimum prize money and prizes,

3-       Qualifiers:

1. Determined upon car count.

4-       General:

1. Inspections will start at 3pm

                                                               i.       You must be in the inspection line no later than 4pm, if not you may be assessed a $50 penalty fee. Cut off will be determined by officials.

1. Pits OPEN AT 2 p.m. EVENT START TIME IS 6:00 PM.

1. There will be a heat or two of  what we determine as lesser built cars

TRUCKS: Trucks must follow the truck 2010 rules posted on the Stirrin’ Dirt website!

STANDARD DEMOLITION DERBY
SATURDAY, AUGUST 27th

1. Registration:
   

1. REGISTRATION,  Car and Driver free
2. Extra Pit passes will be available.
3. Pit passes will be $25 after 5pm!
4. Wristbands must be worn at all times. If it gets torn off, bring it to us and we will replace it. If you should loose it you must purchase a new one.
5. If the driver or pit crew is under the age of 18, he or she must have a release form from their parent or legal guardian. No one under 16 is allowed to drive. Release forms available upon request on the day of the event.

1-       Registration:

1. a.      REGISTRATION,  Car and Driver free
2. b.      Extra Pit passes will be available.
3. c.       Pit passes will be $25 after 5pm!
4. d.       Wristbands must be worn at all times. If it gets torn off, bring it to us and we will replace it. If you should loose it you must purchase a new one.
5. e.        If the driver or pit crew is under the age of 18, he or she must have a release form from their parent or legal guardian. No one under 16 is allowed to drive. Release forms available upon request on the day of the event.

2-       Payouts:        $10,000 Total minimum money and prizes, payout based on car count.

3-       Qualifiers:

1. a.       Determined upon car count.

4-       General:

1. a.       Inspections will start at 3pm

                                                               i.       You must be in the inspection line no later than 5pm, if not you will be assessed a $50 penalty fee. Cut off will be determined by officials.

                                                             ii.      Heats will be drawn at drivers meeting

1. b.       Pits OPEN AT 4 p.m. EVENT START TIME IS 7:00 PM.

5-       Standard rules apply for 80’s and newer

6-       Stock class rules

Visit www.stirrindirtracing.com for rules and information.

1. Registration:
   

1. REGISTRATION,  Car and Driver free
2. Extra Pit passes will be available.
3. Pit passes will be $25 after 6pm!
4. Wristbands must be worn at all times. If it gets torn off, bring it to us and we will replace it. If you should loose it you must purchase a new one.
5. If the driver or pit crew is under the age of 18, he or she must have a release form from their parent or legal guardian. No one under 16 is allowed to drive. Release forms available upon request on the day of the event.

HOT ROCKN’ 4^TH

JULY 4^TH

$22,000

1- Registration:

1. a. Registration opens on Jan 1^st
2. b. 60 car limit and 10 Truck limit

1. c. Please mail your registration fee and registration to:

4670 South 4650 West         West Haven         Utah       84401

Or send in your donation and register at Stirrindirtracing.com

1. d. Entrance fees will be deposited upon receipt and non-refundable. A standby list will be created as people do cancel. If you cancel your Donation will not be refunded or carried over.
2. e. Cost of Registration is $150 for new drivers and $125 for returning drivers.  Trucks will be $50.Registrations will be taken on a first come first serve basis. You must submit your registration form and ENTRANCE FEE in full to reserve your spot and car number. If paying by check or money order, please make it out to

“The American Dream Foundation”

1. f. With registration you will be receiving the following:
   1. i. Cars will receive 3 pit passes and 2 general Admission Tickets. DVD of the event
   2. ii. Trucks will receive 2 pit passes and one general admission ticket. DVD’s are $20
   3. iii. Extra Pit passes will be available at $20 each.
   4. iv. Driver T-shirt
   5. v. Pit passes will be $30 after 4pm!

2- Payouts:                $22,000 Total prize money

1. a. Main event

First            $5000    Trophy                   Fourth    $500       Trophy

Second       $2500    Trophy                   Fifth       $250       Trophy

Third          $1000    Trophy

1. b. Heats:
   1. i. Top TWO will receive $1000 each, and Trophy
   2. ii. Third place from the heats will receive $150
   3. iii. Most aggressive from each heat will receive $200

1. c. Grudge match pays $150 for each qualifier
2. d. Trucks pay $2000 money, split will be decided by truck drivers

3- Qualifiers:

1. a. Top Three cars from each heat.
2. b. Top Two cars from each of the grudge match(s).
3. c. Possible 16 for the Main.

4- General:

1. a. General Rules apply for both cars and Trucks
2. b. All cars must be completely built upon arrival, as you will be staged for your heats prior to the start of the derby.  PLEASE MAKE SURE YOUR CAR IS COMPLETE BEFORE GETTING INSPECTED.
3. c. Upon approved inspection you will receive your flag and draw your heat and stage your car.
4. d. Inspections will be from 10:30am until 3 pm.
   1. i. You must be in the inspection line no later than 2 pm, if not.  If you arrive after 2 pm you may be assessed a $50 late fee or not allowed to run pending time and head officials call. DO NOT BE LATE!
   2. ii. ALL cars must be in staging area no later than 5 pm.
   3. iii. Heats will be drawn and cars staged at this time. Staged cars will be secured. You may hook up a battery charger or remove the battery once staged and reinstall after 5pm. You may cover your car if you wish.
5. e. Access to cars will be allowed after 5 pm.
6. f. Drivers meeting will be at 5 pm
7. g. EVENT START TIME IS 6:00 PM.

Visit www.stirrindirtracing.com for rules and information including hotels

1-      Registration:

1. a.      REGISTRATION,  Car and Driver free
2. b.      Extra Pit passes will be available
3. c.       Pit passes will be $25 after 5pm!
4. d.      Wristbands must be worn at all times. If it gets torn off, bring it to us and we will replace it. If you should loose it you must purchase a new one.
5. e.       If the driver or pit crew is under the age of 18, he or she must have a release form from their parent or legal guardian. No one under 16 is allowed to drive. Release forms available upon request on the day of the event.

2-      Payouts:      $5000 Total minimum money and prizes, payout based on car count.

3-      Qualifiers:

1. a.      Determined upon car count.

4-      General:

1. a.      Inspections will start at 3pm

                                                           i.       You must be in the inspection line no later than 4pm, if not you will be assessed a $50 penalty fee. Cut off will be determined by officials.

                                                         ii.      Heats will be drawn at drivers meeting

1. b.      Pits OPEN AT 2 p.m. EVENT START TIME IS 7:00 PM.

1. c.       Standard rules apply

Visit www.stirrindirtracing.com for rules and information.

1-       Registration:

1. a.       Registration fee is $150 per team, REFUNDED upon arrival
2. b.       Driver and car are FREE
3. c.        Extra Pit passes will be available.
4. d.       After 5pm pit passes will be $25
5. e.        Wristbands must be worn at all times. If it gets torn off, bring it to us and we will replace it. If you should loose it you must purchase a new one.
6. f.        If the driver or pit crew is under the age of 18, he or she must have a release form from their parent or legal guardian. No one under 16 is allowed to drive. Release forms available upon request on the day of the event.

2-       Payouts:        $15000 Total minimum money and prizes, payout based on car count.

3-       Qualifiers:

1. a.       Determined upon car count.

4-       General:

1. a.       Inspections will start at 3pm

           i.       You must be in the inspection line no later than 4pm, if not you will be assessed a $50 penalty fee. Cut off will be determined by officials.

          ii.      Heats will be drawn at drivers meeting

1. b.       Pits OPEN AT 2 p.m. EVENT START TIME IS 7:00 PM.

5-    Standard build rules apply for all cars and Trucks.

6-   Cars will be teams of 2

1. a.    All teams must be painted the same color scheme,
2. b.    Only one BLACK colored team will be allowed.
3. c.    You must call to reserve your color, first come first serve
4. d.    This year’s winner will have first choice for next year’s color